2VV-33C-R4-V4
8-port multibeam antenna, 8x 1695–2690 MHz, 4x 33° HPBW, 4xRET
Features and benefits
- Enhances network capacity and spectrum utilization when used in six sector applications
- Reduces antenna count to minimize Cap-Ex and Op-Ex costs – 3 antennas required for 6 sector configurations
- Utilizes RET-PMOD-A20-4A24
Specifications
General specifications
| Antenna Type | Multibeam |
| Band | Single band |
| Color | Light Gray (RAL 7035) |
| Grounding Type | RF connector inner conductor and body grounded to reflector and mounting bracket |
| Performance Note | Outdoor usage |
| Radome Material | Fiberglass, UV resistant |
| Radiator Material | Low loss circuit board |
| Reflector Material | Aluminum |
| RF Connector Interface | 7-16 DIN Female |
| RF Connector Location | Bottom |
| RF Connector Quantity, high band | 8 |
| RF Connector Quantity, mid band | 0 |
| RF Connector Quantity, low band | 0 |
| RF Connector Quantity, total | 8 |
Remote electrical tilt (ret) information
| RET Hardware | CommRET v2 |
| RET Interface | 2x 8 pin connector as per IEC 60130-9 Daisy chain in: Male / Daisy chain out: Female Pin3: RS485A(AISG_B), Pin5: RS485B(AISG_A), Pin6: DC 10~30V, Pin7: DC_ Return |
| RET Interface, quantity | 1 female | 1 male |
| Input Voltage | 10–30 Vdc |
| Internal RET | High band (4) |
| Power Consumption, active state, maximum | 10 W |
| Power Consumption, idle state, maximum | 2 W |
| Protocol | 3GPP/AISG 2.0 (Single RET) |
Dimensions
| Width | 395 mm | 15.551 in |
| Depth | 228 mm | 8.976 in |
| Length | 2499 mm | 98.386 in |
| Net Weight, without mounting kit | 30.4 kg | 67.020 lb |
Array layout
| Click on image to enlarge. |
Port configuration
| Click on image to enlarge. |
Electrical specifications
| Impedance | 50 ohm |
| Operating Frequency Band | 1695 – 2690 MHz |
| Polarization | ±45° |
| Total Input Power, maximum | 1,200 W @ 50 °C |
Electrical specifications
| Frequency Band, MHz | 1695–1880 | 1850–1990 | 1920–2180 | 2300–2400 | 2490–2690 |
| Gain, dBi | 19.0 | 19.4 | 19.6 | 20.0 | 20.1 |
| Beam Centers, Horizontal, degrees | ±27 | ±27 | ±27 | ±27 | ±27 |
| Beamwidth, Horizontal, degrees | 40 | 39 | 37 | 36 | 31 |
| Beamwidth, Vertical, degrees | 7.9 | 7.4 | 7 | 6.2 | 5.7 |
| Beam Tilt, degrees | 2–12 | 2–12 | 2–12 | 2–12 | 2–12 |
| Horizontal Sidelobe, dB | 18 | 18 | 18 | 18 | 17 |
| USLS (First Lobe), dB | 16 | 16 | 16 | 17 | 20 |
| Front-to-Back Ratio at 180°, dB | 31 | 36 | 38 | 36 | 35 |
| Isolation, Cross Polarization, dB | 30 | 30 | 30 | 30 | 30 |
| Isolation, Inter-band, dB | 30 | 30 | 30 | 30 | 30 |
| Isolation, Beam to Beam, dB | 28 | 28 | 28 | 28 | 28 |
| VSWR | Return loss, dB | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 |
| PIM, 3rd Order, 2 x 20 W, dBc | -153 | -153 | -153 | -153 | -153 |
| Input Power per Port at 50°C, maximum, watts | 200 | 200 | 200 | 200 | 200 |
Electrical specifications, basta
| Frequency Band, MHz | 1695–1880 | 1850–1990 | 1920–2180 | 2300–2400 | 2490–2690 |
| Gain by all Beam Tilts, average, dBi | 18.6 | 19.0 | 19.3 | 19.5 | 19.7 |
| Gain by all Beam Tilts Tolerance, dB | ±0.5 | ±0.4 | ±0.4 | ±0.5 | ±0.4 |
| Gain by Beam Tilt, average, dBi | 2 ° | 17.7 7 ° | 17.9 12 ° | 17.7 |
2 ° | 18.3 7 ° | 18.7 12 ° | 18.5 |
2 ° | 18.6 7 ° | 19.0 12 ° | 18.7 |
2 ° | 19.1 7 ° | 19.5 12 ° | 19.3 |
2 ° | 19.4 7 ° | 19.9 12 ° | 19.4 |
| Beamwidth, Horizontal Tolerance, degrees | ±2.6 | ±1.8 | ±2.3 | ±1.5 | ±1.8 |
| Beamwidth, Vertical Tolerance, degrees | ±0.4 | ±0.3 | ±0.5 | ±0.3 | ±0.2 |
| USLS, beampeak to 20° above beampeak, dB | 16 | 16 | 16 | 17 | 20 |
| Front-to-Back Total Power at 180° ± 30°, dB | 24 | 26 | 27 | 29 | 28 |
| CPR at Boresight, dB | 21 | 24 | 19 | 21 | 19 |
| CPR at 10 dB Horizontal Beamwidth, dB | 11 | 16 | 16 | 14 | 10 |
Mechanical specifications
| Wind Loading @ Velocity, frontal | 525.0 N @ 150 km/h (118.0 lbf @ 150 km/h) |
| Wind Loading @ Velocity, lateral | 386.0 N @ 150 km/h (86.8 lbf @ 150 km/h) |
| Wind Loading @ Velocity, maximum | 898.0 N @ 150 km/h (201.9 lbf @ 150 km/h) |
| Wind Loading @ Velocity, rear | 540.0 N @ 150 km/h (121.4 lbf @ 150 km/h) |
| Wind Speed, maximum | 241 km/h (150 mph) |
Packaging and weights
| Width, packed | 505 mm | 19.882 in |
| Depth, packed | 386 mm | 15.197 in |
| Length, packed | 2631 mm | 103.583 in |
| Weight, gross | 44.4 kg | 97.885 lb |
Regulatory compliance/certifications
| Agency | Classification |
CHINA-ROHS
|
Above maximum concentration value |
| ISO 9001:2015 | Designed, manufactured and/or distributed under this quality management system |
| ROHS | Compliant/Exempted |
| UK-ROHS | Compliant/Exempted |
General specifications
| Antenna Type | Multibeam |
| Band | Single band |
| Color | Light Gray (RAL 7035) |
| Grounding Type | RF connector inner conductor and body grounded to reflector and mounting bracket |
| Performance Note | Outdoor usage |
| Radome Material | Fiberglass, UV resistant |
| Radiator Material | Low loss circuit board |
| Reflector Material | Aluminum |
| RF Connector Interface | 7-16 DIN Female |
| RF Connector Location | Bottom |
| RF Connector Quantity, high band | 8 |
| RF Connector Quantity, mid band | 0 |
| RF Connector Quantity, low band | 0 |
| RF Connector Quantity, total | 8 |
Remote electrical tilt (ret) information
| RET Hardware | CommRET v2 |
| RET Interface | 2x 8 pin connector as per IEC 60130-9 Daisy chain in: Male / Daisy chain out: Female Pin3: RS485A(AISG_B), Pin5: RS485B(AISG_A), Pin6: DC 10~30V, Pin7: DC_ Return |
| RET Interface, quantity | 1 female | 1 male |
| Input Voltage | 10–30 Vdc |
| Internal RET | High band (4) |
| Power Consumption, active state, maximum | 10 W |
| Power Consumption, idle state, maximum | 2 W |
| Protocol | 3GPP/AISG 2.0 (Single RET) |
Dimensions
| Width | 395 mm | 15.551 in |
| Depth | 228 mm | 8.976 in |
| Length | 2499 mm | 98.386 in |
| Net Weight, without mounting kit | 30.4 kg | 67.020 lb |
Electrical specifications
| Impedance | 50 ohm |
| Operating Frequency Band | 1695 – 2690 MHz |
| Polarization | ±45° |
| Total Input Power, maximum | 1,200 W @ 50 °C |
Electrical specifications
| Frequency Band, MHz | 1695–1880 | 1850–1990 | 1920–2180 | 2300–2400 | 2490–2690 |
| Gain, dBi | 19.0 | 19.4 | 19.6 | 20.0 | 20.1 |
| Beam Centers, Horizontal, degrees | ±27 | ±27 | ±27 | ±27 | ±27 |
| Beamwidth, Horizontal, degrees | 40 | 39 | 37 | 36 | 31 |
| Beamwidth, Vertical, degrees | 7.9 | 7.4 | 7 | 6.2 | 5.7 |
| Beam Tilt, degrees | 2–12 | 2–12 | 2–12 | 2–12 | 2–12 |
| Horizontal Sidelobe, dB | 18 | 18 | 18 | 18 | 17 |
| USLS (First Lobe), dB | 16 | 16 | 16 | 17 | 20 |
| Front-to-Back Ratio at 180°, dB | 31 | 36 | 38 | 36 | 35 |
| Isolation, Cross Polarization, dB | 30 | 30 | 30 | 30 | 30 |
| Isolation, Inter-band, dB | 30 | 30 | 30 | 30 | 30 |
| Isolation, Beam to Beam, dB | 28 | 28 | 28 | 28 | 28 |
| VSWR | Return loss, dB | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 |
| PIM, 3rd Order, 2 x 20 W, dBc | -153 | -153 | -153 | -153 | -153 |
| Input Power per Port at 50°C, maximum, watts | 200 | 200 | 200 | 200 | 200 |
Electrical specifications, basta
| Frequency Band, MHz | 1695–1880 | 1850–1990 | 1920–2180 | 2300–2400 | 2490–2690 |
| Gain by all Beam Tilts, average, dBi | 18.6 | 19.0 | 19.3 | 19.5 | 19.7 |
| Gain by all Beam Tilts Tolerance, dB | ±0.5 | ±0.4 | ±0.4 | ±0.5 | ±0.4 |
| Gain by Beam Tilt, average, dBi | 2 ° | 17.7; 7 ° | 17.9;12 ° | 17.7 | 2 ° | 18.3; 7 ° | 18.7;12 ° | 18.5 | 2 ° | 18.6; 7 ° | 19.0;12 ° | 18.7 | 2 ° | 19.1; 7 ° | 19.5;12 ° | 19.3 | 2 ° | 19.4; 7 ° | 19.9;12 ° | 19.4 |
| Beamwidth, Horizontal Tolerance, degrees | ±2.6 | ±1.8 | ±2.3 | ±1.5 | ±1.8 |
| Beamwidth, Vertical Tolerance, degrees | ±0.4 | ±0.3 | ±0.5 | ±0.3 | ±0.2 |
| USLS, beampeak to 20° above beampeak, dB | 16 | 16 | 16 | 17 | 20 |
| Front-to-Back Total Power at 180° ± 30°, dB | 24 | 26 | 27 | 29 | 28 |
| CPR at Boresight, dB | 21 | 24 | 19 | 21 | 19 |
| CPR at 10 dB Horizontal Beamwidth, dB | 11 | 16 | 16 | 14 | 10 |
Mechanical specifications
| Wind Loading @ Velocity, frontal | 525.0 N @ 150 km/h (118.0 lbf @ 150 km/h) |
| Wind Loading @ Velocity, lateral | 386.0 N @ 150 km/h (86.8 lbf @ 150 km/h) |
| Wind Loading @ Velocity, maximum | 898.0 N @ 150 km/h (201.9 lbf @ 150 km/h) |
| Wind Loading @ Velocity, rear | 540.0 N @ 150 km/h (121.4 lbf @ 150 km/h) |
| Wind Speed, maximum | 241 km/h (150 mph) |
Packaging and weights
| Width, packed | 505 mm | 19.882 in |
| Depth, packed | 386 mm | 15.197 in |
| Length, packed | 2631 mm | 103.583 in |
| Weight, gross | 44.4 kg | 97.885 lb |
| Click on image to enlarge. |
| Click on image to enlarge. |
Regulatory compliance/certifications
| Agency | Classification |
|
CHINA-ROHS
|
Above maximum concentration value |
| ISO 9001:2015 | Designed, manufactured and/or distributed under this quality management system |
| ROHS | Compliant/Exempted |
| UK-ROHS | Compliant/Exempted |
Documentation & downloads
Assembly drawing
Product information
Product specification
Assembly drawing
Product compliance documentation
Product information
Product specification
Related products & accessories
Included products
Base station antennas
-
BSAMNT-3 Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set.
Included products
Base station antennas
-
BSAMNT-3 Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set.